Manual.ly Logo

Benning DUSPOL digital Handleiding

5,0 · 3 Beoordelingen

PDF handleiding · 91 Pagina's

Nederlands

M: QW-35-FL
pagina

/ 91

Loading...
f6617ca8dc3778b540c3f3c17acb02139854 page b
02/ 2019
DUSPOL
®
digital
8
sure a capacitive coupling to earth.
- Apply the probe tips L1/-
2
and L2/+
3
to two external
conductors (phases) and check whether the external con-
ductor voltage of e.g. 400 V is applied.
- A clockwise phase sequence (phase L1 before phase L2)
is given, if the green LED „►“ of the phase sequence in-
dication
L
and the symbol of the phase sequence
indication
P
light up on the LC display
6
.
- A counter-clockwise phase sequence (phase L2 before
phase L1) is given, if the green LED „◄“ of the phase
sequence indication
L
and the symbol of the phase
sequence indication
P
light up on the LC display
6
.
- The phase sequence test always requires a countercheck
with the probe tips L1/-
2
and L2/+
3
being inverted dur-
ing which the phase sequence must change.
Note:
The phase sequence test can be carried out in an earthed
three-phase mains from 400 V - 900 V, 50/60 Hz (phase to
phase) on. Protective clothing and insulating conditions on site
might impair the function.
8. Continuity test (gure I)
- The continuity test must be carried out on system parts
which are free of voltage. If necessary, capacitors have to
be discharged.
- Apply the two probe tips L1/-
2
and L2/+
3
to the system
parts to be tested.
- In case of continuity (R < 100 kΩ), an acoustic signal is
emitted and the yellow LED Ω
M
for continuity lights up.
- If a voltage is applied to the test point, the voltage tester
automatically switches over to the voltage test function
and indicates this function.
9. Resistance measurement (gure J)
- The resistance measurement must be carried out on sys-
tem parts which are free of voltage. If necessary, capaci-
tors have to be discharged.
- Short-circuit the probe tips L1/-
2
and L2/+
3
and press
the push-button
7
of the display handle L2
9
once until
the kΩ symbol and „Ohm“ are shown on the LC display
6
. Display: „OL“ stands for a measured value which is
outside the measuring range.
- The resistance measurement function is active for approx.
10 seconds.
- Apply the probe tips L1/-
2
and L2/+
3
to the system
parts to be tested in order to measure resistances from
0.1 kΩ to 300 kΩ.
Note:
If required, it is possible to carry out a null balance with the
resistance measurement function being activated. For this pur-
pose, short-circuit the probe tips L1/-
2
and L2/+
3
and press
and hold the push-button
7
of the display handle L2
9
for
approx. 2 seconds until „0.0“ kΩ is shown on the LC display.
10. Diode test (gures K/L)
- The diode test must be carried out on system parts which
are free of voltage. If necessary, capacitors have to be dis-
charged.
- Short-circuit the probe tips L1/-
2
and L2/+
3
and press
the push-button
7
of the display handle L2
9
twice until
the diode symbol and „diod“ are shown on the LC
display
6
. Display: „OL“ VDC
- The diode test is active for approx. 10 seconds.
- Apply the probe tip L1/-
2
to the cathode and the probe
tip L2/+
3
to the anode of the diode to determine the con-
ducting-state voltage between 0.3 V and 2 V. In case of a
defective (broken down) diode, a voltage value of approx.
0.0 V will be displayed.
- In case of a diode tested in non-conducting direction, the
LC display shows „OL“.
11. Cable break detector (gure M)
- The cable break detector is intended for the non-contact
localization of cable breaks on exposed live lines.
- Switch the voltage tester on by briefly actuating the push-
button
7
of the display handle L2
9
(remains switched
on for approx. 10 seconds!). When the device is switched
on, the display shows „0.0“.
- Fully grasp the display handle L2
9
and pass the detec-
tor
5
over a live line (e.g. a cable reel or a chain of lights)
from the feeding point (phase) in direction of the other end
of the line.
- As long as the line is not interrupted, the yellow LED Ω
M
for continuity is flashing.
- The point of the cable break has been localized as soon as
the yellow LED Ω
M
goes out.
Note:
The cable break detector may grounded power from 230 V,
50/60 Hz (phase to earth) are used. Insulating protective cloth-
ing and site conditions can affect the function.
12. Measuring point/display illumination (gure N)
- The measuring point illumination
4
can be switched on
with the probe tips being open by actuating the push-but-
ton
7
of the display handle L2
9
(1 second).
- The off automatically after 10 seconds
- The background lighting of the LC display
6
is activated
automatically by means of a light sensor
N
.
13. Battery replacement (gure O)
- Do not apply voltage to the device when the battery com-
partment is open!
- Please replace the batteries as soon as the
symbol
is shown on the LC display
6
.
- The battery compartment is located on the back of the dis-
play handle L2/+
9
.
- Unscrew the screw of the battery compartment cover and
replace the used batteries by two new micro batteries
(LR03/AAA).

Chat met je Benning DUSPOL digital-handleiding via AI

Krijg direct AI-antwoorden uit je Benning DUSPOL digital-handleiding

Vraag alles over Benning DUSPOL digital. Antwoorden komen uit deze handleiding, met de pagina's waarop ze zijn gebaseerd.

DUSPOL digital Onderhoudsschema

Naar behoefte
Vervang de batterijen wanneer het symbool voor lage batterij verschijnt

Vervang de twee Micro LR03/AAA-batterijen zodra het symbool voor lege batterijen op het LC-scherm wordt weergegeven.

Voor en na elk gebruik
Voer een functionele test uit voordat u de afwezigheid van spanning controleert

Controleer de spanningszoeker direct voor en na gebruik op correcte werking om veiligheid te waarborgen.

Bij langdurige opslag
Verwijder de batterijen uit het apparaat tijdens opslag

Als het apparaat gedurende een langere periode wordt opgeslagen, verwijder dan de batterijen uit het apparaat om schade te voorkomen.

Naar behoefte
Reinig behuizing en batterijcompartiment met een droge doek

Reinig de buitenkant van het apparaat en eventuele verontreinigingen in het batterijgedeelte met een schone, droge doek.

M: qwen/qwen3.8-flash

Stel eenVraag

0/1000

Beveel je DUSPOL digital aan?

Ja Nee
0
User Pic

Dan King

4 maanden geleden

Is er een kalibratieservice nodig voor dit apparaat, of kan ik die overslaan?

0
User Pic

Manual.ly

4 maanden geleden

Op basis van gebruikersfeedback is de kalibratiedienst niet nodig. Het apparaat vervult zijn beoogde functie nauwkeurig uit de doos zonder extra kalibratiestappen.

M: QW-35-FL
M: QW-35-FL
0
User Pic

Jaleel Marquardt

6 maanden geleden

Waarom zaten er al batterijen in de verpakking toen ik het item ontving?

M: QW-35-FL

Veelgestelde Vragen

A

Voer een functionele test uit door de meetpuntspunten kortsluiten en de drukknop drie seconden ingedrukt houden. De zoemer moet geluid maken en alle LEDs en displaysegmenten moeten oplichten. U moet het ook testen op een bekende spanningsbron zoals een 230 V stopcontact.

Is dit antwoord nuttig?

A

Ja, door de sonde samen te kortsluiten en de knop drie keer in te drukken totdat Lo U verschijnt. Dit activeert een laagspanningsbereik waarmee metingen van 1,0 V tot 11,9 V mogelijk zijn, hoewel frequentie-aanduiding in deze modus uitgeschakeld is.

Is dit antwoord nuttig?

A

De trillingsmotor helpt bij het onderscheiden tussen bedrijfsspanning en interferentiespanningen. Door beide knoppen te activeren, schakelt u over naar een modus met lage interne weerstand die reactieve spanningen onderdrukt en condensatoren ontladt.

Is dit antwoord nuttig?

A

Zoek de batterijcompartiment aan de achterkant van het displayhandvat. Draai het deksel los, verwijder de oude AAA-batterijen, plaats twee nieuwe waarbij u de juiste polariteit in acht neemt, en draai het deksel weer strak vast.

Is dit antwoord nuttig?

A

Het heeft een IP65-classificatie, wat betekent dat het stofdicht is en beschermd tegen waterstralen. Het kan in regen worden gebruikt, maar mag niet onder water worden gedompeld.

Is dit antwoord nuttig?

A

Als de spanning 1.050 V AC of 1.250 V DC overschrijdt, geeft het display OL weer en flitsen alle stap-indicator LEDs om waarschuwing voor overbelasting te geven.

Is dit antwoord nuttig?

M: QW-35-FL

Voordelen en Nadelen

Voordelen

  • Onderscheidt tussen bedrijfsspanning en interferentiespanningen met behulp van een laadverbinding en trillingsmotor
  • Uitgebreide testmogelijkheden inclusief continuïteit, weerstand, diode en kabelbreukdetectie
  • Hoge veiligheidsclassificatie met IP65-bescherming tegen stof en waterstralen voor gebruik in ruige omgevingen
  • Automatische zelftestfunctie zorgt ervoor dat alle componenten zoals LEDs en zoemer correct werken voordat ze worden gebruikt
  • Tweepootsontwerp met geïsoleerde grepen zorgt voor veilige behandeling tijdens testen onder spanning
VS

Nadelen

  • Vereist een minimale spanning van 9 V om te activeren, wat het gebruik op zeer lage vermogensbronnen beperkt zonder speciale modus
  • Batterijduur kan worden verminderd tijdens uitgebreide lasttests vanwege de hoge stroomafname van de trillingsmotor
  • Fasenvolgordeaanduiding werkt alleen in aarded netwerken bij 50/60 Hz, wat de wereldwijde toepasbaarheid beperkt
  • Kan niet worden gebruikt met het batterijcompartiment open, wat zorgvuldig beheer van stroomtoegang vereist
  • Maximale bedrijfstijd is beperkt tot 30 seconden om oververhitting te voorkomen, waardoor pauzes nodig zijn tijdens langdurig testen
M: QW-35-FL

Product Specificatie

Meetbereik

1-1000V

M: QW-35-FL

Product Beschrijving

Benning digitaal spanningsonderzoeker met tas - Essentiële veiligheid voor professionals

De Benning digitaal spanningsonderzoeker met tas is een robuust en betrouwbaar gereedschap dat is ontworpen voor gekwalificeerde elektriciens die precisie en veiligheid in hun dagelijkse werk eisen. Dit apparaat, bekend als de DUSPOL digitaal, vertegenwoordigt een belangrijke vooruitgang in elektrische testapparatuur door meerdere diagnostische functies te combineren in één ergonomisch toestel. Of u nu controleert op afwezigheid van spanning, fasenvolgorde test of kabelbreuken lokaliseert, deze tester biedt duidelijke visuele en auditieve feedback om uw veiligheid te waarborgen.

Uitgerust met een intuïtief LC-display en een multi-niveau LED-indicator, biedt de tester onmiddellijk inzicht in de elektrische omgeving. Het kan wisselstroom tot 1.000 V en gelijkstroom tot 1.200 V met hoge nauwkeurigheid meten. De inclusie van een trillingsmotor stelt gebruikers in staat om onderscheid te maken tussen bedrijfsspanning en interferentiespanningen, een kritieke functie bij het werken met complexe installaties waar lekstromen vals lezen kunnen veroorzaken. Het apparaat schakelt automatisch in wanneer het een spanning van minimaal 9 V detecteert, zodat u nooit verrast wordt tijdens een inspectie.

Ontworpen met gebruikersveiligheid als topprioriteit, beschikt de tester over geïsoleerde handvatten en vereist een specifieke tweepooltest om de afwezigheid van spanning te bevestigen, conform strikte veiligheidsnormen zoals DIN EN 61243-3. De ingebouwde zelftestfunctie verifieert de integriteit van de zoemer, LEDs en display vóór elk gebruik, waardoor u vertrouwen krijgt in uw resultaten. Bovendien maakt de laagspanningsmodus precieze metingen mogelijk tot 1,0 V, waardoor het veelzijdig is voor diverse toepassingen buiten standaard netspanningcontroles.

Het pakket bevat een duurzame draagtas, die het instrument beschermt tegen stof, vocht en fysieke schade tijdens transport. Met zijn IP65-classificatie is de tester bestand tegen waterstralen en stof, waardoor hij geschikt is voor gebruik in ruige industriële omgevingen of onder openluchtcondities. Regelmatig onderhoud is eenvoudig en bestaat uit alleen een droge doek voor reiniging en tijdige batterijvervanging met standaard AAA-cellen. Voor professionals die op zoek zijn naar een uitgebreide oplossing voor elektrische diagnose, steekt de Benning digitaal spanningsonderzoeker met tas uit als een vertrouwd metgezel die functionaliteit, duurzaamheid en veiligheid combineert.

M: QW-35-FL

© Copyright 2026 Manual.ly