Manual.ly Logo

Nolan N100-5 Handleiding

0,0 · 0 Beoordelingen

PDF handleiding · 116 Pagina's

Nederlands

M: GO-GEM-FL-25
pagina

/ 116

Loading...
69fd6a5e58c38ca0373746be471a62d62d3f page 16
22
N100-5
8 CHEEK PAD ASSEMBLY
8.1 Put the left cheek pad against the corresponding polystyrene inner cheek pad,
insert the chin strap into the passageway of the cheek pad padding and push it
near the three buttons on its back in order to fasten them to their seats (Fig.15).
8.2 Repeat these steps with the right cheek pad padding.
Warning: the buttons are not fastened until a click is heard. Check that the strap
comes out properly from the cheek pad padding.
8.3 Insert the chin strap band into the elastic loops on the roll neck (Fig.14).
WARNING
- If your helmet is equipped with the double D-Ring retention system, pull it
down as indicated in the attached double D-Ring label.
- Remove the inner comfort padding only when cleaning or washing is required.
- Never use the helmet if the inner comfort padding and the cheek pads have not
been correctly and completely tted.
- Delicately hand-wash in lukewarm water (max. 30° C) and neutral soap.
- Rinse with cold water and allow drying at room temperature, away from direct
sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get
partially destroyed to help absorb shocks.
- Do not modify or alter the helmet’s internal polystyrene components in any way.
- Clean the inner polystyrene components with a damp cloth only and allow it to dry
at room temperature away from direct sunlight.
- Never use tools or equipment of any sort to carry out the steps described above.
9 ADJUSTING THE ROLL NECK STRETCH
The roll neck stretch can be adjusted to adapt to the different sizes or riding positions
of the riders.
9.1 To increase the roll neck stretch press the button of the left strap clip and simulta-
neously pull the elastic strap towards the rear part of the helmet (Fig. 23). Follow
the same steps on the other side of the helmet.
9.2 To decrease the roll neck stretch press the button of the left strap clip button and
simultaneously push the rear part of the roll neck to loosen the stretch of the elas-
tic strap (Fig. 24). Follow the same steps on the other side of the helmet.
9.3 Wear and fasten the helmet (see instructions above) and make sure that the roll
neck stretch in the riding position is satisfactory.
WARNING
After assembling or disassembling the roll neck and/or adjusting the stretch, wear
and fasten the helmet to check the correct adjustment of the chin strap (see at-
tached label), the correct positioning of the helmet on the head in the riding posi-
tion and the VPS functionality in all positioning notches.
3.4 Pull the roll neck towards the inside of the helmet to remove the two rear aps
of the roll neck from the seats on the shell sealing edge and remove it from the
helmet (Fig.20).
4 LINER DISASSEMBLY
4.1 Unhook the left rear ap of the liner from the shell rear edge by slightly puling the
comfort padding towards the inside of the helmet (Fig.21). Follow the same steps
for the right rear ap.
4.2 Hold the left front part of the liner and pull it upwards in order to remove the cor-
responding liner ap from the support xed to the polystyrene inner shell (Fig.22).
Then repeat the same steps for the central front and right ap.
4.3 Completely remove the liner from the helmet.
5 LINER ASSEMBLY
5.1 Insert the liner correctly into the helmet and t it well against the base.
5.2 Insert the central front ap of the liner into its seat on the support xed to the pol-
ystyrene inner shell and push it downwards until it is completely locked (Fig.22).
Then repeat the operation with the left and right aps making sure that the side
ends of the liner are placed between the external side frames and the polystyrene
inner shell.
Warning: Check the correct assembly of the liner front area by lifting and lowering
the VPS. These movements should be smooth. If this is not the case, repeat steps
4.2 and 5.2.
5.3 Insert the rear right and left aps of the liner into the relevant lower seats on the
shell edge (Fig.21). Push the aps until they are fully hooked onto the support.
6 ASSEMBLY OF THE ROLL NECK
6.1 Insert the rear right and left aps of the roll neck into the relevant upper seats on
the shell edge (Fig.20). Push the aps until they are fully hooked onto the support.
6.2 Insert the side ap into the seat on the lining of the left polystyrene cheek pad and
push it towards the inside of the helmet until it is completely locked to the support
(Fig.19).
6.3 Press the front button of the roll neck to fasten it to the corresponding seat on the
lining of the left polystyrene cheek pad (Fig.18).
6.4 Follow the same steps on the other side of the helmet.
7 ASSEMBLY OF THE INNER EXPANDING FOAM PADDING OF THE CHEEK PADS
7.1 Gently put the inner expanding foam padding inside the fabric lining of the left
cheek pad (Fig.17). Carefully spread out the padding while checking that there are
no wrinkles in the cheek pad fabric lining.
7.2 Insert the upper ap “B” and the lower ap “C” of the frame into their loops on the
back of the frame (Fig.16).
7.3 Fasten the three eyelets “A” of the rear frame of the left cheek pad next to the three
snap buttons (top, front and rear) on its back (Fig.16).
7.4 Repeat these steps with the right cheek pad padding.
INSTRUCTIONS FOR USE

Chat met je Nolan N100-5-handleiding via AI

Krijg direct AI-antwoorden uit je Nolan N100-5-handleiding

Vraag alles over Nolan N100-5. Antwoorden komen uit deze handleiding, met de pagina's waarop ze zijn gebaseerd.

N100-5 Onderhoudsschema

Na elk gebruik
Helmpakking en vizier drogen

Laat de helm na gebruik op een geventileerde plaats drogen met het vizier open. Weghouden van warmtebronnen.

Naar behoefte
PINLOCK binnenvizier schoonmaken

Verwijder het binnenvizier en maak voorzichtig schoon met neutrale vloeibare zeep en een vochtige doek. Afspoelen onder stromend water.

Periodiek
PINLOCK rek controleren

Controleer regelmatig de juiste rek om verplaatsing en krassen op oppervlakken te voorkomen.

Naar behoefte
Gekrast vizier vervangen

Als het vizier beschadigd is of diep gekrast waardoor het zicht wordt verminderd, vervang het dan onmiddellijk.

Naar behoefte
Comfortkussens wassen

Alleen handwassen in lauw water (max 30 C) met neutrale zeep. Niet in de wasmachine wassen.

M: QW-35-FL

Stel eenVraag

0/1000

Beveel je N100-5 aan?

Ja Nee

Veelgestelde Vragen

A

Het is een modulaire motorhelm met een opklapbare kinbescherming, een viziersysteem, interne zonwering en comfortgerichte functies voor dagelijks gebruik op de weg.

Is dit antwoord nuttig?

A

De hoogzichtbare afwerking helpt de rijder beter op te vallen in het verkeer, wat vooral handig kan zijn in drukke stedelijke gebieden, bij weinig licht of bij wisselvallig weer.

Is dit antwoord nuttig?

A

De kinbescherming gebruikt een tweetraps openingsproces met afzonderlijke ontgrendel- en openingshendels. Dat maakt bediening met één hand makkelijker en helpt onbedoeld openen te verminderen.

Is dit antwoord nuttig?

A

Ja. De helm ondersteunt een vizierstand met minimale opening voor luchtstroom en kan ook een Pinlock-binnenscherm gebruiken om beslaan in vochtige of koude omstandigheden te verminderen.

Is dit antwoord nuttig?

A

Ja. De wangstukken, het nekgedeelte en de voering zijn verwijderbaar, waardoor schoonmaken eenvoudiger wordt en rijders op termijn een betere pasvorm en een frisser interieur behouden.

Is dit antwoord nuttig?

A

Ja. De helm is voorbereid op N-Com-communicatiesystemen, afhankelijk van de uitvoering. Sommige interne schuimdelen moeten mogelijk worden verwijderd tijdens de installatie van compatibele componenten.

Is dit antwoord nuttig?

M: GO-GEM-FL-25

Voordelen en Nadelen

Voordelen

  • Dual Action-kinbescherming verbetert het gebruiksgemak en helpt onbedoeld openen te voorkomen.
  • Het hoogzichtbare ontwerp vergroot de zichtbaarheid van de rijder in verkeer en bij weinig licht.
  • VPS-zonnescherm en optionele Pinlock-ondersteuning verbeteren het zicht bij wisselende weersomstandigheden.
  • Verwijderbare voering en ventilatiesysteem verbeteren het comfort en maken onderhoud eenvoudiger.
VS

Nadelen

  • Het modulaire ontwerp kan complexer aanvoelen dan een eenvoudige integraalhelm.
  • Vizier-, VPS- en Pinlock-onderdelen moeten voorzichtig worden behandeld om krassen of slijtage te voorkomen.
  • Bescherming hangt af van de juiste pasvorm en goede sluiting, dus maatvoering is erg belangrijk.
  • Sommige accessoires en functies kunnen per uitvoering verschillen of afzonderlijke installatie vereisen.
M: GO-GEM-FL-25

Product Specificatie

Type

Modulaire Helm

Kenmerken

Geintegreerd Zonnevizier

Gewicht

1,65 kg

M: GO-GEM-FL-25

Product Beschrijving

Nolan N100-5 Hoge zichtbaarheid (verschillende maten)

De Nolan N100-5 Hi-Visibility is ontworpen voor rijders die een praktische modulaire helm willen met een sterke focus op veiligheid, zichtbaarheid en dagelijks comfort. Ontworpen voor gebruik op de motor combineert hij een opklapbare kinbescherming, een helder viziersysteem en een hoogzichtbare afwerking waardoor de rijder beter opvalt in het verkeer. Het geheel voelt modern, functioneel en gemaakt voor echt dagelijks rijden.

Een van de opvallendste kenmerken is het Dual Action-kinbeschermingssysteem. Dit mechanisme is ontworpen om met één hand te worden geopend en helpt tegelijk het risico op onbedoeld openen te verkleinen. Rijders kunnen schakelen tussen een volledig gesloten stand voor maximale bescherming en een open stand voor gemak bij stops of in langzamer verkeer. Die flexibiliteit maakt de helm aantrekkelijk voor zowel forenzen als tourrijders.

Zichtbaarheid is een andere grote troef. De helm ondersteunt een standaard buitenscherm, een minimale openingsstand voor luchtstroom en ontwaseming, en een intern VPS-zonnescherm voor heldere omstandigheden. Voor rijders die te maken hebben met wisselend weer biedt het optionele Pinlock-binnenscherm extra ondersteuning tegen beslaan. Samen helpen deze elementen om een helderder zicht op de weg te behouden wanneer de temperatuur daalt, de luchtvochtigheid stijgt of het zonlicht fel wordt.

Comfort en aanpasbaarheid krijgen ook veel aandacht. De verwijderbare binnenvoering, wangstukken en nekgedeelte zijn bedoeld om de pasvorm te verbeteren en het schoonmaken te vereenvoudigen. Het ventilatiesysteem helpt frisse lucht door de helm te leiden, warmteopbouw te verminderen en het beslaan van het vizier te beperken. Daarnaast is de helm voorbereid op N-Com-communicatiesystemen, waardoor hij een slimme keuze is voor rijders die verbonden willen blijven zonder in te leveren op comfort.

Opmerkingen

  • Het meest geschikt voor rijders die op zoek zijn naar een modulaire helm met sterke veelzijdigheid voor dagelijks gebruik.
  • Verkrijgbaar in verschillende maten, dus de pasvorm moet zorgvuldig worden gecontroleerd op stabiliteit en comfort.
  • Volg de reinigings- en onderhoudsinstructies om het vizier, de voering en het zonnescherm te beschermen.
  • Regelmatige inspectie van banden, vizieronderdelen en vergrendelingssystemen helpt de prestaties in de loop van de tijd te behouden.
  • Het hoogzichtbare ontwerp voegt een praktisch veiligheidsvoordeel toe in druk verkeer en bij weinig licht.
M: GO-GEM-FL-25

© Copyright 2026 Manual.ly