Manual.ly Logo

GYS TIG 200 DC HF FV Handleiding

0,0 · 0 Beoordelingen

PDF handleiding · 80 Pagina's

Nederlands

M: GO-GEM-FL-25
pagina

/ 80

Loading...
336d0675033ab5e56257cc17c9ee58c43e6e page 10
16
TIG 168 / TIG 200 DC
MADE IN FRANCE
EN
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualied person. Annual maintenance is recommended.
• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out main-
tenance work. DANGER High Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the
electrical connections checked by a qualied person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be
replaced by the manufacturer, its after sales service or an equally qualied person.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
INSTALLATION – FONCTIONNEMENT PRODUIT
DESCRIPTION
The TIG 168/200 HF are portable, single phase ventilated Inverter welding units to be used with non-consumable elec-
trodes (TIG) in direct current (DC). TIG DC welding requires a gaseous protection (Argon). In MMA mode, it allows you
to weld with any kind of electrode : rutile, basic, stainless steel or cast iron. The TIG 168 work with a single phase 230V
input. The TIG 200 FV works on a single phase input between 85V to 265V. They are all protected for a use on electric
generators. The TIG 200 can be equipped with a remote control or foot pedal (This option is supplied separately).
ALIMENTATION-MISE EN MARCHE
• This machine is tted with a 16A socket type CEE7/7 which must be connected to a single-phase 230V (50 - 60 Hz)
power supply tted with three wires and one earthed neutral.
The absorbed effective current (I1eff) is displayed on the machine, for optimal use. Check that the power supply and
its protection (fuse and/or circuit breaker) are compatible with the current needed by the machine. In some countries,
it may be necessary to change the plug to allow the use at maximum settings.
• To start the machine up, press the Standby Button «
»
• NB: If the screen displays
. this indicates that the device has entered protection mode. This will occur if the
power supply voltage is excessively high (over 265V). If the machine switches on in protection mode, unplug the device
and plug it into a socket delivering the correct voltage.
CONNECTION ON A GENERATOR
The machine can work with generators as long as the auxiliary power matches these requirements :
- The voltage must be AC, always set as specied, and the peak voltage below 400V,
- The frequency must be between 50 and 60 Hz.
It is imperative to check these requirements as several generators generate high voltage peaks that can damage these
machines.
MMA WELDING (ELECTRODE)
Getting Started
• Connect the electrode holder and earth clamp to the corresponding sockets.
• Ensure that the welding polarities and intensities indicated on the electrode packaging are observed.
• Remove the electrode from the electrode holder when the machine is not in use.
Welding Features:
Your device is equipped with 3 specic functions :
Hot Start gives an adjustable* overcurrent at the beginning of the welding.
Arc Force delivers an overcurrent which avoids sticking when the electrode enters the weld pool.
Anti-Sticking allows easy removal of the electrode in case of sticking.
Selection of process and current setting
1- Select MMA mode 2- Select the desired current using the potentiometer
Nb. : The TIG 200FV, the welding current will vary depending on the power supply voltage used:
- on 110V, the current can be set from 10 to 120A.
- on 230V, the current can be set from 10 to 200A.

Chat met je GYS TIG 200 DC HF FV-handleiding via AI

Krijg direct AI-antwoorden uit je GYS TIG 200 DC HF FV-handleiding

Vraag alles over GYS TIG 200 DC HF FV. Antwoorden komen uit deze handleiding, met de pagina's waarop ze zijn gebaseerd.

TIG 200 DC HF FV Onderhoudsschema

Herinner mij wanneer onderhoud nodig is
Jaarlijks
Algemeen onderhoudscontrole

Laat een gekwalificeerde persoon routineonderhoud uitvoeren en elektrische veiligheid verifiëren.

Elke 4 maanden
Behuizing verwijderen en stof reinigen

Verwijder het deksel 2 tot 3 keer per jaar om overtollig stof met perslucht te verwijderen.

Gratis onderhoudsherinneringen

Afgestemd op uw aankoopdatum. Altijd gratis, op elk moment afmelden.

Door te verzenden gaat u akkoord met het privacybeleid. U kunt zich met een klik afmelden in elke e-mail.
M: QW-35-FL

Stel eenVraag

0/1000

Beveel je TIG 200 DC HF FV aan?

Ja Nee

Veelgestelde Vragen

A

Hij is vooral geschikt voor DC TIG-lassen met argonbescherming, maar ondersteunt ook MMA-elektrodelassen. Daardoor is hij handig voor precisiewerk, reparaties en algemene werkplaatstaken.

Is dit antwoord nuttig?

A

Ja. HF-start zorgt voor contactloze ontsteking en schone starts, terwijl Lift-modus handig is wanneer starts met hoge frequentie niet geschikt zijn of wanneer minder interferentie de voorkeur heeft.

Is dit antwoord nuttig?

A

Ja, de machine is ontworpen om te werken met compatibele generators, mits de uitgang stabiel is en voldoet aan de vereiste spannings- en frequentielimieten.

Is dit antwoord nuttig?

A

In MMA-modus kan hij rutiel-, basische, roestvrijstalen en gietijzeren elektroden verwerken. In TIG DC-modus is hij bedoeld voor staal en vergelijkbare DC-compatibele materialen.

Is dit antwoord nuttig?

A

Deze modi helpen de warmte-inbreng te verminderen en verbeteren de controle bij dunne delen of gevoelige verbindingen. Ze helpen ook vervorming te beperken en creëren een beter gecontroleerd smeltbad.

Is dit antwoord nuttig?

A

Ja, hij heeft vijf geheugenplaatsen voor het opslaan en terugroepen van veelgebruikte TIG-instellingen, wat herhalingswerk versnelt en helpt om lasparameters consistent te houden.

Is dit antwoord nuttig?

M: GO-GEM-FL-25

Voordelen en Nadelen

Voordelen

  • Het brede spanningsbereik van het FV-model ondersteunt onstabiele of gemengde stroomomstandigheden op locatie.
  • HF- en Lift-startopties zorgen voor een schonere boogontsteking in verschillende omgevingen.
  • TIG-, MMA-, Pulse-, Easy Pulse-, Spot- en geheugenfuncties vergroten de veelzijdigheid.
  • Compatibiliteit met afstandsbediening en voetpedaal helpt de lasstroom nauwkeurig af te stellen.
VS

Nadelen

  • TIG-lassen vereist beschermgas, dus extra voorbereiding en verbruiksartikelen zijn nodig.
  • Geavanceerde instellingen kunnen voor beginners tijd kosten om onder de knie te krijgen.
  • De machine is alleen bedoeld voor DC-lassen en niet voor AC-toepassingen.
  • Goede ventilatie en strikte veiligheidsmaatregelen zijn essentieel tijdens gebruik.
M: GO-GEM-FL-25

Product Specificatie

Vermogen

7 kW (110-230 V)

Nullastspanning

76 V

Regelbereik

5-200 A (TIG)

Afmetingen

310x420x150 mm (HxWxD)

Gewicht

12,00 kg

M: GO-GEM-FL-25

Product Beschrijving

GYS TIG 200 DC HF FV inverter lasmachine: compact vermogen voor nauwkeurig lassen

De GYS TIG 200 DC HF FV inverter lasmachine incl. accessoires handleiding verwijst naar een veelzijdige machine voor lassers die controle, draagbaarheid en betrouwbare prestaties willen. Deze inverter is ontworpen voor DC TIG-lassen met argonbescherming en ondersteunt ook MMA-elektrodelassen voor routinereparaties en algemeen gebruik in de werkplaats.

Gebouwd voor flexibiliteit

Een van de opvallende sterke punten van de TIG 200 DC HF FV is het brede ingangsbereik van de FV-versie, waardoor het een praktische keuze is voor locaties waar de netspanning niet altijd ideaal is. Hij is ook geschikt voor gebruik met een generator, wat de mobiliteit vergroot voor werkzaamheden op locatie, onderhoudsteams en installateurs. De machine combineert HF-ontsteking voor schone, contactloze boogstarts met Lift-modus voor omgevingen waar starten met hoge frequentie niet de voorkeur heeft.

Handige functies voor schonere resultaten

Deze lasser biedt verschillende functies die helpen de boogkwaliteit en lasafwerking te verbeteren. Twee- en vierstaps triggermodi maken lange lassen comfortabeler, terwijl 4T Log een handige schakeloptie biedt tussen warme en koude stroom tijdens het lassen. Pulse en Easy Pulse verminderen de warmte-inbreng, wat vooral handig is bij dunne materialen of wanneer vervorming beperkt moet blijven. Er is ook een Spot-modus beschikbaar voor hechten van onderdelen vóór het definitief lassen.

Praktische bediening en opslag

De interface is gericht op snelle instelling en reproduceerbare resultaten. Gebruikers kunnen de voorstroom, opbouwtijd, lasstroom, pulsfrequentie, koude stroom, afbouwtijd en nagas instellen op basis van verbinding en materiaal. Vijf geheugenplaatsen maken het mogelijk veelgebruikte instellingen snel op te slaan en terug te roepen. In compatibele configuraties zorgt afstandsbediening of een voetpedaal voor nog fijnere stroomregeling.

Waarom hij opvalt

Voor hobbyisten met hogere eisen en professionals die een betrouwbaar DC TIG-platform nodig hebben, biedt deze machine een uitgebalanceerde mix van draagbaarheid en functionaliteit. Hij ondersteunt roestvrij staal, zacht staal, gietijzer en rutiel- of basiselektroden in MMA-modus. De meegeleverde accessoires en de duidelijke logica van het besturingssysteem maken het eenvoudiger om van instelling naar productie te gaan zonder tijdverlies.

Opmerkingen

  • Zorg voor goede ventilatie en volledige beschermende uitrusting tijdens het lassen.
  • Voor TIG-gebruik is argonbescherming vereist.
  • Laat de toorts afkoelen vóór onderhoud.
  • Houd kabels volledig afgerold om oververhitting te voorkomen.
M: GO-GEM-FL-25

© Copyright 2026 Manual.ly