Manual.ly Logo

Dremel Stylo+ 2050 Handleiding

4,0 · 4 Beoordelingen

PDF handleiding · 164 Pagina's

Nederlands

M: GO-GEM-FL-25
pagina

/ 164

Loading...
9c8eef9c2a66ff041a179419530e90183af9 page 9
SAFETY INSTRUCTIONS FOR
ALL OPERATIONS
SAFETY WARNINGS COMMON FOR GRINDING,
SANDING, WIRE BRUSHING, POLISHING, CARVING OR
ABRASIVE CUTTING-OFF OPERATIONS
a. This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
Read all safety warnings, instructions, illustrations

Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
b. 
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
c. The rated speed of the grinding accessories must
be at least equal to the maximum speed marked on
the power tool. Grinding accessories running faster
than their rated speed can break and y apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately controlled.
e. The arbour size of wheels, sanding drums or any

collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss
of control.
f. Mandrel mounted wheels, sanding drums, cutters
or other accessories must be fully inserted into
the collet or chuck. If the mandrel is insufciently
held and/or the overhang of the wheel is too long, the
mounted wheel may become loose and be ejected at
high velocity.
g. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, sanding drum for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
h. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various operations.
The dust mask or respirator must be capable of
ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
i. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
j. Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
k. 
the start-up. The reaction torque of the motor, as it
accelerates to full speed, can cause the tool to twist.
l. Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one
hand and the tool in the other hand while in use.
Clamping a small workpiece allows you to use your
hand(s) to control the tool. Round material such as
dowel rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to bind or jump
toward you.
m. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
n. Never lay the power tool down until the accessory
has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
o. After changing the bits or making any adjustments,
make sure the collet nut, chuck or any other
adjustment devices are securely tightened. Loose
adjustment devices can unexpectedly shift, causing
loss of control, loose rotating components will be
violently thrown.
p. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
q. Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
r. 
materials. Sparks could ignite these materials.
s. Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, sanding band, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory’s rotation.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a. 
your body and arm to allow you to resist kickback
forces. The operator can control kickback forces, if
proper precautions are taken.
b. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
c. Do not attach a toothed saw blade. Such blades
create frequent kickback and loss of control.
d. Always feed the bit into the material in the same
direction as the cutting edge is exiting from the
material (which is the same direction as the chips
are thrown). Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this feed.
9

Chat met je Dremel Stylo+ 2050-handleiding via AI

Krijg direct AI-antwoorden uit je Dremel Stylo+ 2050-handleiding

Vraag alles over Dremel Stylo+ 2050. Antwoorden komen uit deze handleiding, met de pagina's waarop ze zijn gebaseerd.

Stylo+ 2050 Onderhoudsschema

Regelmatig
Reinigen van ventilatieopeningen en schakelhendels

Houd luchtopeningen en schakelhendels schoon en vrij van vreemde stoffen met behulp van droge perslucht. Steek geen puntige voorwerpen in.

Voor elk gebruik
Controleer accessoires op beschadiging

Controleer slijpschijven op splinters en scheuren, zandtrommels op scheuren of slijtage en draadborstels op losse draden vóór elke bewerking.

M: QW-35-FL

Stel eenVraag

0/1000

Beveel je Stylo+ 2050 aan?

Ja Nee
0
User Pic

Benoît Hamel

8 maanden geleden

Ik vind de knop voor de boorkopvergrendeling onhandig. Als ik hem uitzet, druk ik er per ongeluk op samen met de aan/uit-knop en dan maakt hij een krakend geluid. Is dit normaal, en hoe kan ik dit voorkomen?

0
User Pic

Manual.ly

8 maanden geleden

De schakelaar voor de spankopvergrendeling zit tegenover de aan/uit-knop, dus het gelijktijdig indrukken van beide kan een kort mechanisch geluid veroorzaken. Om dit te voorkomen, zorg ervoor dat de spankopvergrendeling niet is ingeschakeld wanneer u het apparaat uitschakelt: schakel eerst de stroom uit en ontgrendel de spankop daarna met uw andere hand (of pauzeer kort zodat uw vingers niet op beide knoppen rusten). Hierna kunt u de normale werking hervatten. Als het geluid aanhoudt, zelfs wanneer u voorzichtig bent om niet beide knoppen tegelijk in te drukken, probeer dan het gebied rond de schakelaar schoon te maken en controleer op zichtbare obstakels. Als het probleem aanhoudt, neem dan contact op met de supportafdeling met een korte video, zodat we het apparaat kunnen bekijken.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Veelgestelde Vragen

A

Hij is het meest geschikt voor gedetailleerde taken zoals graveren, polijsten, schuren, snijden, reinigen en licht snijwerk. Door zijn slanke vorm is hij vooral handig wanneer precisie belangrijker is dan kracht.

Is dit antwoord nuttig?

A

Ja, deze uitvoering wordt geleverd met accessoires, waardoor hij direct klaar is voor uiteenlopende kleine projecten. De meegeleverde tools vergroten de mogelijkheden van de slijper en ondersteunen creatievere toepassingen.

Is dit antwoord nuttig?

A

Ja. Het gereedschap heeft een variabele snelheidsregeling, zodat je de prestaties kunt afstemmen op het materiaal en de klus. Lagere snelheden zijn handig voor polijsten; hogere snelheden passen beter bij hardere materialen.

Is dit antwoord nuttig?

A

Ja. Het taps toelopende, penachtige ontwerp is gemaakt voor controle en comfort. Het voelt natuurlijk aan in de hand en is ideaal voor fijne, geleide bewegingen over kleine oppervlakken.

Is dit antwoord nuttig?

A

Gebruik goede oog- en stofbescherming, vermijd overmatige druk en zorg dat accessoires stevig zijn gemonteerd. Kies ook de juiste snelheid voor het materiaal om schade te voorkomen.

Is dit antwoord nuttig?

A

Hij is beter geschikt voor precisiewerk en licht gebruik dan voor zwaar slijpwerk. Voor intensieve materiaalafname is een groter en krachtiger gereedschap een betere keuze.

Is dit antwoord nuttig?

M: GO-GEM-FL-25

Voordelen en Nadelen

Voordelen

  • Slanke grip in penstijl maakt gedetailleerd werk eenvoudiger en comfortabeler.
  • Variabele snelheidsregeling helpt bij verschillende materialen en taken.
  • Compatibel met meerdere accessoires voor polijsten, graveren, schuren en snijden.
  • Lichtgewicht ontwerp vermindert vermoeidheid tijdens langere projecten.
VS

Nadelen

  • Niet ideaal voor zwaar slijpwerk of agressieve materiaalafname.
  • Voor het beste resultaat zijn zorgvuldige snelheidskeuze en een lichte aanraking nodig.
  • Bij sommige accessoires is wat oefening nodig voor correct monteren en balanceren.
  • Stof, geluid en veiligheidsmaatregelen blijven belangrijk tijdens gebruik.
M: GO-GEM-FL-25

Product Specificatie

Type

Rechtslijper

Vermogen

9 W (230 V)

Onbelast toerental

5000-22000/min

Gereedschapshouder

0,8-3,2 mm snelspanboorkop, spantang

Bijzondere kenmerken

Toerentalregeling

Gewicht

110 g

Leveringsomvang

15-delige accessoireset

M: GO-GEM-FL-25

Product Beschrijving

Dremel Stylo+ elektrische rechte slijper met accessoires (2050-15)

De Dremel Stylo+ elektrische rechte slijper is ontworpen voor mensen die precisie willen in een slank, gemakkelijk vast te houden formaat. De penachtige behuizing ligt natuurlijk in de hand, wat vooral handig is voor detailwerk waarbij controle belangrijker is dan brute kracht. Met de meegeleverde accessoires wordt dit compacte gereedschap een flexibele partner voor polijsten, reinigen, graveren, schuren, snijden en lichte snijtaken.

Een klein gereedschap met grote veelzijdigheid

Een van de aantrekkelijkste eigenschappen van de Stylo+ is hoe toegankelijk hij aanvoelt. In plaats van een grote behuizing biedt hij een taps toelopende vorm die fijne, geleide bewegingen ondersteunt. Dat maakt hem een slimme keuze voor hobbyprojecten, afwerking van knutselwerk, modelbouw en delicate reparaties. De variabele snelheidsregeling voegt nog een laag gebruiksgemak toe, zodat je het gereedschap kunt aanpassen aan het materiaal en de klus.

Gemaakt voor gedetailleerd werk

De meegeleverde handleiding benadrukt de juiste snelheidskeuze en veilig gebruik, wat veel zegt over het doel van het gereedschap: het presteert het best bij licht en gecontroleerd gebruik. De slijper werkt met een reeks Dremel-accessoires, en het klauwplaat-systeem maakt het wisselen van accessoires sneller en eenvoudiger. Voor gebruikers die meer nauwkeurige klemming willen, is ook het spantang-systeem beschikbaar. Die flexibiliteit is een echt voordeel bij het wisselen tussen viltpolijsters, schuurrolletjes, snijfrezen of graveerbits.

Praktische prestaties in dagelijks gebruik

In de kern draait de Stylo+ om gemak en controle. Hij is licht, eenvoudig te manoeuvreren en geschikt voor lange sessies waarbij vermoeidheid van de hand een rol speelt. Het snelheidsbereik van het gereedschap helpt bij het afstemmen op het werkstuk: lagere snelheden zijn beter voor polijsten en gevoelige materialen, terwijl hogere snelheden geschikt zijn voor hout, metaal, glas en vormwerk. Dat maakt hem een betrouwbare keuze voor makers die werken met verschillende oppervlakken en technieken.

Veiligheid en onderhoud zijn belangrijk

Zoals elk roterend gereedschap beloont de Stylo+ zorgvuldig gebruik. De handleiding benadrukt veiligheidsbril, stofbescherming en correcte montage van accessoires als essentieel. Ook wordt gebruikers aangeraden geen overmatige druk uit te oefenen, omdat het gereedschap bedoeld is om het werk door het accessoire te laten doen. Regelmatig reinigen en correct opbergen helpen om het apparaat soepel te laten werken op de lange termijn.

Opmerkingen

  • De beste resultaten komen van het kiezen van het juiste accessoire en de juiste snelheid.
  • Een lichte aanraking verbetert de nauwkeurigheid en vermindert slijtage.
  • Gebruik passende bescherming wanneer stof of vonken kunnen ontstaan.

Kortom, de Dremel Stylo+ is een nette oplossing voor precisiegerichte projecten. Hij combineert draagbaarheid, controle en flexibiliteit in accessoires in een formaat dat uitstekend geschikt is voor gedetailleerd creatief werk.

M: GO-GEM-FL-25

© Copyright 2026 Manual.ly