Manual.ly Logo

Benning MM 6-2 Handleiding

5,0 · 1 Beoordelingen

PDF handleiding · 144 Pagina's

Nederlands

M: QW-35-FL
pagina

/ 144

Loading...
1073337a83fe56817a21cbe9219ad899d4d3 page 1d
02/ 2020
BENNING MM 6-1/ 6-2
29
tivity).
- Connect the red safety measuring lead to the jack
J
for V of the
BENNING MM 6-1/ MM 6-2.
- Bring the safety measuring lead into contact with the measuring point of the
system part.
- If an acoustic signal is emitted and the red LED
N
lights, the phase of an
earthed alternating voltage is applied to this measuring point (system part).
9. Maintenance
Before opening the BENNING MM 6-1/ MM 6-2, ensure that it is
not connected to a source of voltage! Electrical hazard!
Any work required on the BENNING MM 6-1/ MM 6-2 when it is under voltage must
be done only by a qualified electrician. Special steps must be taken to prevent
accidents. Before opening the BENNING MM 6-1/ MM 6-2, remove it from all sources
of voltage as follows:
- First remove both safety measuring leads from the measurement points.
- Remove both safety measuring leads from the BENNING MM 6-1/ MM 6-2
- Turn the rotating switch
to “OFF”.
9.1 Securing the unit
Under certain circumstances, the safety of the BENNING MM 6-1/ MM 6-2 can
no longer be guaranteed. This may be the case if:
- there are visible signs of damage on the unit,
- errors occur in measurements,
-
the unit has been stored for a long period of time under the wrong conditions, and
- if the unit has been subjected to rough handling during transport.
In these cases, the BENNING MM 6-1/ MM 6-2 must be switched off immediately,
removed from the measuring points and secured to prevent it from being used again.
9.2 Cleaning
Clean the outside of the unit with a clean dry cloth. (Exception: any type of
special cleaning cloth). Never use solvents or abrasives to clean the testing unit.
Ensure that the battery compartment and the battery contacts have not been
contaminated by electrolyte leakage.
If any electrolyte or white deposits are seen near to the battery or in the battery
compartment, remove them with a dry cloth, too.
9.3 Battery replacement
Before opening the BENNING MM 6-1/ MM 6-2, ensure that it is
not connected to a source of voltage! Electrical hazard!
The BENNING MM 6-1/ MM 6-2 is supplied by means of one 9 V block battery.
Battery replacement (see figure 13) is required as soon as all segments of the
battery symbol
3
have disappeared and the battery symbol is flashing.
To replace the battery, proceed as follows:
- First remove the safety measuring leads from the measurement circuit.
- Remove the safety measuring leads from the BENNING MM 6-1/ MM 6-2.
- Turn the rotating switch
to “OFF”.
- Remove the protective rubber holster
M
from the BENNING MM 6-1/ MM 6-2.
- Lay the BENNING MM 6-1/ MM 6-2 on its front and loosen the screw from
the cover of the battery compartment.
- Lift off the battery compartment cover from the bottom part of the battery
compartment.
- Lift the discharged battery out of the battery compartment and remove the
battery leads carefully from the battery.
- Connect the new battery with the battery leads and arrange them in such a
way that they are not crushed between the two halves of the housing. Then
place the battery in the correct position in the battery compartment.
- Clip the battery cover onto the bottom part and tighten the screws.
- Replace the BENNING MM 6-1/ MM 6-2 in its protective rubber holster
M
.
See fig. 13: Battery replacement
Remember the environment! Do not dispose of used batteries
with domestic waste. Dispose of them at a battery-collection
point or as toxic waste. Your local authority will give you the
information you need.

Chat met je Benning MM 6-2-handleiding via AI

Krijg direct AI-antwoorden uit je Benning MM 6-2-handleiding

Vraag alles over Benning MM 6-2. Antwoorden komen uit deze handleiding, met de pagina's waarop ze zijn gebaseerd.

MM 6-2 Onderhoudsschema

Herinner mij wanneer onderhoud nodig is
Jaarlijks
Kalibreer de multimeter

Stuur het apparaat naar het Benning Service Center voor herkalibratie om de gespecificeerde nauwkeurigheid te behouden. Aanbevolen interval is één jaar.

Regelmatig
Reinig de behuizing

Veeg de buitenkant van het toestel af met een schone, droge doek of speciale schoonmaakdoek. Gebruik geen oplosmiddelen of schuurmiddelen.

Naar behoefte
Vervang de 9V-batterij

Vervang de batterij wanneer alle segmenten in het batterijsymbool verdwijnen en het symbool knippert.

Voor elk gebruik
Controleer apparaat en meetkabels

Controleer het instrument en de meetkabels op tekenen van schade voordat u begint met werken. Zorg dat het niet per ongeluk kan worden gebruikt als het beschadigd is.

Gratis onderhoudsherinneringen

Afgestemd op uw aankoopdatum. Altijd gratis, op elk moment afmelden.

Door te verzenden gaat u akkoord met het privacybeleid. U kunt zich met een klik afmelden in elke e-mail.
M: qwen/qwen3.8-flash

Stel eenVraag

0/1000

Beveel je MM 6-2 aan?

Ja Nee
0
User Pic

Margarita Simonis

4 maanden geleden

Detecteert deze multimeter automatisch of ik wisselspanning of gelijkspanning meet?

0
User Pic

Manual.ly

4 maanden geleden

Ja, de Benning MM 6-2 beschikt over een AutoV-functie die automatisch vaststelt of de gemeten waarde gelijkstroom (DC) of wisselstroom (AC) is. Dit zorgt voor nauwkeurige metingen zonder handmatig schakelen. Het apparaat heeft ook een functie voor automatische uitschakeling na 20 minuten om de batterijlevensduur te verlengen en wordt geleverd met een beschermende holster met een magneet voor handenloos gebruik.

M: QW-35-FL
M: QW-35-FL
0
User Pic

Jace Lowe

6 maanden geleden

Is de batterij inbegrepen in de doos of moet ik deze apart kopen?

M: QW-35-FL

Veelgestelde Vragen

A

Het apparaat is geclassificeerd voor CAT IV 600 V tussen geleider en grond, en CAT III 1000 V voor lijn-tot-lijn metingen. Het mag niet worden gebruikt in circuits die deze limieten overschrijden.

Is dit antwoord nuttig?

A

Ja, maar alleen als het is uitgerust met de optionele Type K draad temperatuursensor. De standaard unit meet direct voltage, stroom, weerstand, frequentie en capaciteit.

Is dit antwoord nuttig?

A

Er verschijnt een batteriesymbool op het display. Wanneer alle segmenten verdwijnen en het symbool begint te knipperen, moet de batterij onmiddellijk worden vervangen om meetfouten te voorkomen.

Is dit antwoord nuttig?

A

Nee, het apparaat is ontworpen voor droge omgevingen alleen. Het heeft een IP30-rating, wat geen bescherming biedt tegen waterindringing.

Is dit antwoord nuttig?

A

De blauwe functietoets selecteert secundaire functies voor de roterende schakelposities, zoals schakelen tussen AC/DC stroomtypes of inschakelen van frequentiemetingmodi.

Is dit antwoord nuttig?

A

Benning beveelt aan het apparaat jaarlijks te kalibreren door het naar hun servicecentrum te sturen om de gespecificeerde nauwkeurigheidspecificaties te behouden die gegarandeerd zijn voor het eerste jaar.

Is dit antwoord nuttig?

M: QW-35-FL

Voordelen en Nadelen

Voordelen

  • True RMS-meting voor nauwkeurige lezingen op niet-sinusvormige signalen
  • CAT IV 600V en CAT III 1000V veiligheidsrating voor risicovolle omgevingen
  • VoltSense niet-contact spanningsdetectie met audio en visuele waarschuwingen
  • Automatische bereikselectie vereenvoudigt bediening voor snelle diagnostiek
  • Duurzame rubberen hoes met geïntegreerde magneet voor handenloos gebruik
VS

Nadelen

  • Temperatuurmeting vereist een apart K-type sensortoestelaccessoire
  • Geen achtergrondverlichting voor lage lichtomstandigheden
  • Batterijvervanging vereist het verwijderen van de beschermende rubberen hoes
  • Handmatige bereikschakeling kan minder intuïtief zijn dan volledig automatische modellen
  • Maximale spanning tegen aarde is beperkt tot 600V in CAT IV-instellingen
M: QW-35-FL

Product Specificatie

Meetbereik

max. 10A, max. 1000V, max. 40MΩ

Inhoud verpakking

Zak

M: QW-35-FL

Product Beschrijving

Benning MM 6-2 Multimeter: Precisie en Veiligheid voor Professionals

De Benning MM 6-2 Multimeter staat als een robuust gereedschap ontworpen voor elektriciens en technisch opgeleide individuen die hoge nauwkeurigheid in hun metingen eisen. Dit digitale apparaat blinkt uit in droge omgevingen, met een uitgebreide reeks functies waaronder gelijkspanning, wisselspanning, weerstand, diodetest, continuïteitscontrole, capaciteitsmeting, frequentieanalyse en temperatuurmonitoring via de optionele K-type sensor. De True RMS-faciliteit zorgt voor betrouwbare lezingen zelfs bij niet-sinusvormige golven, wat het onmisbaar maakt voor complexe elektrische diagnostiek.

Veiligheid is van cruciaal belang in het ontwerp van de Benning MM 6-2. Geclassificeerd voor CAT IV 600 V en CAT III 1000 V, biedt het een veilige omgeving voor werken aan hoogspanningscircuits wanneer gebruikt met passende veiligheidskabels en beschermende doppen. Het apparaat beschikt over VoltSense-technologie voor niet-contact spanningsdetectie, waardoor gebruikers worden gewaarschuwd voor onder spanning staande fasen door een akoestische zoemer en rode LED-indicator zonder fysiek contact. Het slimme display bevat een bargrafiek voor het visualiseren van trends en automatische uitschakeling om de levensduur van de langdurige 9-volt batterij te behouden, die tot wel 200 uur kan gaan op alkaline-voeding.

Ergonomie is ook in overweging genomen, met een duurzaam rubberen beschermingsframe dat het apparaat beschermt tegen mechanische schade. Dit frame fungeert ook als standaard voor makkelijker lezen en bevat een magneet voor handenloze werking. De meegeleverde compacte draagtas en veiligheidskabels zorgen ervoor dat de multimeter altijd klaar is voor directe inzet op elke werkplek. Of het nu gaat om het controleren van continuïteit met een zoemer of het meten van microampère, de Benning MM 6-2 levert de precisie die vereist is voor professioneel elektrisch werk.

M: QW-35-FL

© Copyright 2026 Manual.ly