Manual.ly Logo

Benning MM 5-1 Handleiding

0,0 · 0 Beoordelingen

PDF handleiding · 137 Pagina's

Nederlands

M: QW-35-FL
pagina

/ 137

Loading...
109c1933695fa1714032b8c4405a5d0ae7d5 page 1d
02/ 2020
BENNING MM 5-1/ 5-2
29
In these cases, the BENNING MM 5-1/ MM 5-2 must be switched off immediately,
removed from the measuring points and secured to prevent it from being used again.
9.2 Cleaning
Clean the outside of the unit with a clean dry cloth. (Exception: any type of
special cleaning cloth). Never use solvents or abrasives to clean the testing unit.
Ensure that the battery compartment and the battery contacts have not been
contaminated by electrolyte leakage.
If any electrolyte or white deposits are seen near to the battery or in the battery
compartment, remove them with a dry cloth, too.
9.3 Battery replacement
Before opening the BENNING MM 5-1/ MM 5-2, ensure that it is
not connected to a source of voltage! Electrical hazard!
The BENNING MM 5-1/ MM 5-2 is supplied by means of two integrated 1.5 V
micro (AAA) batteries. Battery replacement (see figure 13) is required as soon
as all segments of the battery symbol
3
have disappeared and the battery
symbol is flashing.
To replace the battery, proceed as follows:
- First remove the safety measuring leads from the measurement circuit.
- Remove the safety measuring leads from the BENNING MM 5-1/ MM 5-2.
- Turn the rotating switch
to “OFF”.
- Remove the protective rubber holster
M
from the BENNING MM 5-1/ MM 5-2.
- Lay the BENNING MM 5-1/ MM 5-2 on its front and loosen the screw from
the cover of the battery compartment.
- Lift off the battery compartment cover from the bottom part of the battery
compartment.
- Remove the discharged batteries from the battery compartment.
- Insert the new batteries into the battery compartment observing correct
po larity.
- Clip the battery cover onto the bottom part and tighten the screw.
- Replace the BENNING MM 5-1/ MM 5-2 in its protective rubber holster
M
.
See fig. 13: Battery replacement
Remember the environment! Do not dispose of used batteries
with domestic waste. Dispose of them at a battery-collection
point or as toxic waste. Your local authority will give you the
information you need.
9.4 Fuse replacement (BENNING MM 5-2)
Before opening the BENNING MM 5-2, ensure that it is not
connected to a source of voltage! Electrical hazard!
The BENNING MM 5-2 is protected against overload by means of an inte grated
fuse (G melt insert) 15 A rapid (see figure 14). Proceed as follows to replace
the fuse:
- Disconnect the safety measuring leads from the measurement circuit.
- Disconnect the safety measuring leads from the BENNING MM 5-2.
- Turn the rotating switch
to the “OFF” position.
- Remove the protective rubber holster
M
from the BENNING MM 5-2.
- Lay the BENNING MM 5-2 on its front and loosen the screw from the cover
of the battery compartment.
- Lift off the battery compartment cover from the bottom part of the battery
compartment.
Do not loosen any of the screws on the printed circuit of the
BENNING MM 5-2!
- Remove the four outer screws (black) from the bottom part of the housing.
- Lift the housing base at the bottom and remove it from the top of the front part.
- Lift one end of the defective fuse out of the fuse holder.
- Push the defective fuse out of the fuse holder completely.
- Replace the defective fuse with another of the same rated power, same trig-
gering characteristics and same dimensions.
- Push the new fuse into the centre of the holder.
- Clip the housing base into the front part and replace the four screws.
- Clip the battery cover onto the bottom part and tighten the screw.
- Replace the BENNING MM 5-2 in its protective rubber holster
M
.
See fig. 14: Fuse replacement

Chat met je Benning MM 5-1-handleiding via AI

Krijg direct AI-antwoorden uit je Benning MM 5-1-handleiding

Vraag alles over Benning MM 5-1. Antwoorden komen uit deze handleiding, met de pagina's waarop ze zijn gebaseerd.

MM 5-1 Onderhoudsschema

Herinner mij wanneer onderhoud nodig is
Jaarlijks
Kalibreer het apparaat bij de fabrieksservice

Stuur het instrument naar Benning Service Center voor herkalibratie om de gespecificeerde nauwkeurigheid te behouden. Aanbevolen interval is één jaar.

Regelmatig
Reinig de buitenkant van de behuizing

Veeg de buitenkant van het toestel af met een schone, droge doek. Gebruik geen oplosmiddelen of schuurmiddelen.

Gratis onderhoudsherinneringen

Afgestemd op uw aankoopdatum. Altijd gratis, op elk moment afmelden.

Door te verzenden gaat u akkoord met het privacybeleid. U kunt zich met een klik afmelden in elke e-mail.
M: qwen/qwen3.8-flash

Stel eenVraag

0/1000

Beveel je MM 5-1 aan?

Ja Nee

Veelgestelde Vragen

A

De Benning MM 5-1 kan veilig spanningen tot 600 V DC of AC meten in Categorie III schakelingen en tot 300 V in Categorie IV schakelingen ten opzichte van aarde.

Is dit antwoord nuttig?

A

Nee, het Benning MM 5-1 model heeft geen ingebouwde temperatuurmeetmogelijkheden. Deze functie is beschikbaar op het Benning MM 5-2 model dat een K-type thermokoppel ondersteunt.

Is dit antwoord nuttig?

A

Schakel het apparaat uit, verwijder de rubberen holster, draai de achterkant los, haal de oude batterijen eruit, plaats nieuwe 1.5 V microbatterijen met de juiste polariteit en assembleer het apparaat opnieuw.

Is dit antwoord nuttig?

A

De VoltSensor functie stelt u in staat om de aanwezigheid van wisselspanning tegen aarde te detecteren zonder fysiek contact, aangegeven door een rode LED en een symbool op het scherm.

Is dit antwoord nuttig?

A

Nee, het apparaat is strikt ontworpen voor droge omgevingen. Gebruik in natte omstandigheden of hoge luchtvochtigheid kan veiligheid en nauwkeurigheid in gevaar brengen.

Is dit antwoord nuttig?

A

Benning beveelt aan het apparaat elk jaar opnieuw te kalibreren om de gespecificeerde meetnauwkeurigheid en naleving van technische specificaties te behouden.

Is dit antwoord nuttig?

M: QW-35-FL

Voordelen en Nadelen

Voordelen

  • True RMS meettechnologie voor nauwkeurige metingen bij niet-sinusvormige signalen
  • VoltSensor functie maakt niet-contact wisselspanningdetectie mogelijk
  • Duurzaam ontwerp met beschermende rubberen holster en magnetische houder
  • Smart HOLD en piekwaardeopslag voor het vastleggen van transiënte data
  • Voldoet aan CAT III 600V en CAT IV 300V veiligheidsnormen
VS

Nadelen

  • Batterijduur kan aanzienlijk afnemen bij koude temperaturen
  • Geen ingebouwde temperatuurmeting (vereist aparte sensor)
  • Kan frequentie niet meten op stroominputten zonder specifieke instelling
  • Vereist handmatige zekeringvervanging voor overstroombeveiliging
  • Beperkt tot droge omgevingen alleen, geen waterbestendigheid
M: QW-35-FL

Product Specificatie

Meetbereik

max. 600 V, max. 100 MΩ

Verpakkingsinhoud

Tas

M: QW-35-FL

Product Beschrijving

De Benning MM 5-1 Multimeter: Precisie en Veiligheid in Elke Meting

De Benning MM 5-1 Multimeter staat als een betrouwbaar hulpmiddel voor elektriciens en technisch opgeleide personen die nauwkeurige diagnose nodig hebben in droge omgevingen. Ontworpen met veiligheid als prioriteit, ondersteunt dit apparaat metingen tot 600 V DC/AC, conform strikte overspanningscategorieën III en IV standaarden. De robuuste constructie omvat een beschermende rubberen holster die het apparaat niet alleen beschermt tegen mechanische schade maar ook een geïntegreerde magneet heeft voor handenloze bediening en een standaard voor gemakkelijker aflezen.

Deze digitale multimeter biedt een uitgebreide suite van functies waaronder gelijkstroomspanning, wisselspanning, weerstand, diodetest en doorverbindingcontrole met een hoorbare zoemer. Het grote 4-cijferige LCD-scherm zorgt voor duidelijke zichtbaarheid van metingen, terwijl functies zoals Smart HOLD en piekwaardeopslag gebruikers in staat stellen om transiënte gegevens moeiteloos vast te leggen. De opname van de VoltSensor-functie maakt niet-contact detectie van wisselspanningen tegen aarde mogelijk, wat een extra laag gemak en veiligheid toevoegt tijdens fase-identificatie taken. Met een meetfrequentie van twee per seconde en automatische bereikselectie, stroomlijnt de Benning MM 5-1 complexe elektrische storingsopsporing tot een naadloos proces.

Het apparaat wordt gevoed door twee standaard 1.5 V microbatterijen, wat ongeveer 300 uur continu gebruik biedt. Het apparaat is uitgerust met een batterijindicator die gebruikers waarschuwt wanneer vervanging nodig is, waardoor onnauwkeurige metingen door lage spanning worden voorkomen. Of u nu circuits controleert, componenten test of storingen diagnosticeert, de Benning MM 5-1 levert consistente prestaties met een garantie op kalibratie van één jaar van de fabrikant.

Samenvatting van Belangrijke Functies

De Benning MM 5-1 combineert duurzaamheid met geavanceerde functionaliteit. Zijn True RMS technologie zorgt voor nauwkeurige metingen zelfs bij niet-sinusvormige golfvormen binnen gespecificeerde limieten. Het apparaat voldoet aan EU-richtlijnen en beschikt over dubbele isolatie voor verhoogde gebruikersbescherming. Onderhoud is eenvoudig, met gemakkelijke toegang voor batterij- en zekeringvervanging, wat lange termijn betrouwbaarheid in professionele instellingen garandeert.

Belangrijke Opmerkingen

Zorg er altijd voor dat het apparaat ontladen is voordat u het opent voor onderhoud. Magneten binnenin het apparaat kunnen pacemakers beïnvloeden, dus houd een veilige afstand als u dergelijke medische implantaten hebt. Gebruik het apparaat niet in natte omstandigheden of buiten zijn gespecificeerde spanningslimieten.

M: QW-35-FL

© Copyright 2026 Manual.ly